PeterStoba
Member
- Joined
- 3 Mar 2017
- Messages
- 14
Just to confirm, no trains have reached Kirkby today, as mentioned earlier. The two freight movements were unaffected.
021 has been pulled from service and is being examined at Birkenhead.Yes they'd almost certainly be D&A tested, as they would for any serious incident such as a spad, collision, derailment etc - it could be argued this incident was all three of those if you take the buffer stop to be a red aspect/end of movement authority.
If mechanical or electrical failure was suspected as the cause then the units would hopefully have been pulled from service for checks & repairs if necessary.
Let's just say enough is known to allow that decision to have been made.
I can't imagine what the passengers must have thought when they saw that!
That is my understanding too...The leading coach at Kirkby was empty of passengers so I believe.
Yes, and rightly so. Plus, regardless of whether any fault is suspected or not, any traction unit or rolling stock that's been involved a collision would have to be inspected.021 has been pulled from service and is being examined at Birkenhead.
In the past did not some terminal stations have rails which were covered with a zig zag type weld to assist stopping?
I believe "wiggly wire" is not for adhesion, but to ensure on lightly used tracks that detection on the signalling system is not lostIn the past did not some terminal stations have rails which were covered with a zig zag type weld to assist stopping?
Manchester Evening News is another title that was a trusted news source until Reach plc bought it a little over a decade ago. Now the stories carry a similar level of factual accuracy as Newsthump.I also look in on some of Reach plc's other web sites Cornwall Live / Devon Live and they are also of poor quality.
Yep - Exactly. Nothing to do with deceleration. Indeed it reduces the contact between wheel and rail and thus may have a very slight detrimental effect on braking performance. It's to concentrate the loads on the rail into a smaller area and thus break through any rust that may have formed, thus ensuring track circuits function reliably. Redundant where axle counters have taken over and was annoying to maintain, and made the rails more difficult to inspect too. Only used where needed!I believe "wiggly wire" is not for adhesion, but to ensure on lightly used tracks that detection on the signalling system is not lost
Sometimes used to ensure reliable track circuit operation at emergency crossovers.I believe "wiggly wire" is not for adhesion, but to ensure on lightly used tracks that detection on the signalling system is not lost
An ECS ended up in the sand drag last year or the year before; first service of the morning. Braking as normal and it just went out from under him; guard and driver both put the emergency in. They rebuilt the sand drag.Those are I believe to improve track circuit contact on rusty rails, not to aid stopping. I half recall Ormskirk had a sand drag at one point but I doubt it does much.
Well then.. It appears 507006’s Kirkby Derailment footage has been found,...
....the unit was going at quite a bit of speed....
Only route i see is left before Wavertree technology park, round the line that goes round Liverpool under Kirkdale depot and joins the South line then reverse down to Sandhills then back up to Kirkby that wayWhat route will 37800 take to get to Kirkby tomorrow? I only ask as I'm not to sure whether there's a link to Kirkdale from Liverpool High Level and Edge Hill.
That video won't be up there long based on the fact the BTP are asking if they have permission....
The other option would presumably be to reverse at southport and sandhills, this would avoid the need to take a diesel loco into the tunnels.Only route i see is left before Wavertree technology park, round the line that goes round Liverpool under Kirkdale depot and joins the South line then reverse down to Sandhills then back up to Kirkby that way
Aaand it's gone!That video won't be up there long based on the fact the BTP are asking if they have permission....
Be great to hear a 37 going through Cressington though.The other option would presumably be to reverse at southport and sandhills, this would avoid the need to take a diesel loco into the tunnels.
Precisely what permission does one need to publish a video taken from a public place (it's from a road bridge, isn't it?) And "outdoor leisure" is permitted now, which would include videography. So I don't see anything at all to get them on.
Sounds like another case of the Police exceeding their authority because they happen not to like something. They seem to be developing quite an aptitude for that at the moment.
My calculation as follows...Can anyone estimate an approximate "impact speed" based on the time taken for one or more carriages to pass a fixed point on the platform (assuming the footage hasn't been speeded up)?
It is, if that is real-time which I guess it is.Crikey, that's a bit quick!
I still had my twitter window open, managed to save the video.Tweet/Video already been took down, just checked.
Looked more like CCTV footage
Definitely CCTV. The camera didn't move at all and it's fair to say most people would have made some movement if they had witnessed that.Ah, I assumed someone had filmed it on their phone. If it was leaked CCTV the BTP probably have a point. There indeed doesn't seem to be anywhere it could have been filmed from manually that would have given the perspective shown.